Home > Insights > EOT Crane vs HOT Crane: What Is the Difference Between Them?
Technical Insight

EOT Crane vs HOT Crane: What Is the Difference Between Them?

Nov 17, 2026
10 min read
EOT Crane vs HOT Crane: What Is the Difference Between Them?

Choosing the right EOT HOT crane decides how fast, how safely and how affordably your plant moves material. An EOT crane lifts and travels with electric motors. A HOT crane relies on hand chains and operator effort. Both run on overhead runway beams, yet they suit very different jobs.

This EOT HOT crane guide compares both types side by side, so you can match the crane to your load, duty cycle and budget. Our engineers at Arvex Cranes, an Ahmedabad-based EOT crane manufacturer, wrote it from 10+ years of shop-floor experience.

EOT HOT Crane Overview

What Is an EOT Crane?

An EOT (Electric Overhead Travelling) crane lifts and moves loads with electric motors. A hoist raises the load, a trolley (crab) carries it across the bridge, and the bridge travels along the runway. The operator controls every motion from a pendant, radio remote or cabin.

Arvex Cranes builds both single girder EOT cranes and double girder EOT cranes in-house, from the girder and end carriage to the hoist and electrical control panel.

What Is a HOT Crane?

A HOT (Hand Operated Travelling) crane works without electricity. The operator pulls a hand chain to lift the load, then pushes the load or pulls a chain to travel along the beam.

Small workshops, maintenance bays and tool rooms choose HOT cranes for occasional, light lifts. You can see the full range on our EOT / HOT crane.

EOT HOT Crane Difference at a Glance

These seven differences matter most when you compare the two cranes.

FeatureEOT CraneHOT Crane
Power sourceElectric motors for hoist, cross travel and long travelHand chain or geared hand operation
Load capacityLight loads up to 100+ tonnesUsually up to about 10 tonnes
SpeedFast, smooth and repeatableSlow, depends on the operator
Duty cycleMedium to heavy, frequent or continuousLight, occasional
Initial costHigher upfront, lower cost per liftLower upfront, higher labour per lift
MaintenanceScheduled electrical and mechanical checksSimple chain, wheel and lubrication checks
Operator and safetyTrained operator, limit switches, overload protectionMinimal training, but strain risk on heavy pulls

Key Differences Between EOT and HOT Cranes

Power, Speed and Productivity

EOT cranes lift and travel at set speeds, so every cycle takes the same time. HOT cranes depend on how hard and how fast the operator pulls. In a plant with frequent lifts, that gap adds up quickly.

Capacity and Duty Class

HOT cranes usually handle loads up to about 10 tonnes, and hand effort rises sharply with weight. EOT cranes cover a far wider range, from light loads to heavy-duty lifts above 100 tonnes.

Engineers also design EOT cranes for a duty class under Indian standards such as IS 3177 and IS 807. This way, the structure matches how often you lift.

Cost and Maintenance

A HOT crane costs less to buy and needs only chain, wheel and lubrication checks. An EOT crane costs more upfront and needs scheduled electrical and mechanical inspection.

However, EOT cranes often lower the cost per lift. They save labour time and cut handling delays.

Safety and Compliance

EOT cranes carry limit switches, overload protection and emergency stops. Under the Factories Act, 1948, lifting machines also need periodic testing and examination by a competent person.

HOT cranes avoid electrical faults. Yet heavy hand-chain pulls raise strain and slip risks. Read this overhead crane overview for basic crane terms, and check the Bureau of Indian Standards before you finalise a specification.

How to Choose the Right EOT HOT Crane

Answer these five questions before you shortlist an EOT HOT crane supplier:

  • Load: What is your heaviest lift? Above 10 tonnes, choose an EOT crane.
  • Frequency: How many lifts do you make per hour? Frequent or continuous lifts need an EOT crane. Occasional lifts suit a HOT crane.
  • Span and height: Wide spans and tall bays favour an EOT crane. Short spans suit a HOT crane.
  • Power: Do you have a reliable power supply? An EOT crane needs it. A HOT crane does not.
  • Budget: Compare the cost per lift over five to ten years, not just the purchase price.

Quick rule: lift often or heavy? Pick an EOT crane. Lift rarely and light? Pick a HOT crane.

Need powered lifting without a full bridge crane? Consider an electric wire rope hoist or electric chain pulley blocks. For outdoor yards, a Goliath crane or jib crane may fit better. Our Goliath crane guide and the Arvex Insights section explain more.

Where Each Crane Works Best

  • EOT cranes: steel plants, fabrication shops, automobile units, warehouses and power plants.
  • HOT cranes: small workshops, maintenance bays, tool rooms and service garages.

EOT HOT Crane Manufacturer and Supplier in Ahmedabad

As an EOT HOT crane manufacturer and EOT HOT crane supplier, Arvex Cranes designs and builds every crane in-house at our Bakrol unit in Ahmedabad. Our team brings 10+ years of experience, 243+ completed projects and 543+ happy customers across India.

Here is what you get when you work with us:

  • In-house design and manufacturing by our own engineers
  • Load testing before every dispatch
  • Custom capacity, span and duty class
  • Pan-India delivery by road
  • Installation, commissioning, operator training and after-sales service

Looking for an EOT crane manufacturer in Ahmedabad or a HOT crane manufacturer in India? Learn more about us or contact our engineering desk.

FAQs

What is the main difference between an EOT crane and a HOT crane?

  • An EOT crane lifts and travels with electric motors, so it suits heavy and frequent lifting. A HOT crane works with hand chains, so it suits light and occasional lifting.

Which is cheaper, an EOT crane or a HOT crane?

  • A HOT crane costs less to buy. An EOT crane often costs less per lift in busy plants because it saves labour time and reduces delays.

What load can a HOT crane lift?

  • Most HOT cranes handle loads up to about 10 tonnes. Hand effort rises sharply with weight, so heavier or frequent lifts need an EOT crane.

Can I upgrade a HOT crane to an EOT crane?

  • Often yes, but engineers must first check the runway beams, columns and building structure. An upgrade usually needs a new bridge, hoist, end carriages and control panel.

How often should an EOT crane be inspected?

  • Operators should check the crane before each shift, and maintenance teams should service it on a schedule. The Factories Act, 1948 also requires periodic testing and examination of lifting machines by a competent person.

Where can I buy an EOT HOT crane in Ahmedabad?

  • Arvex Cranes designs, manufactures and supplies EOT and HOT cranes from Ahmedabad to customers across India. Call +91 7048667796 or email info@arvexcranes.com for a quote.

Conclusion

The right EOT HOT crane depends on your load, lifting frequency and budget. Choose an EOT crane for heavy, frequent lifting. Choose a HOT crane for light, occasional jobs.

Share your capacity, span and duty details, and Arvex Cranes will recommend the right crane. Request a free quote, call +91 7048667796 or email info@arvexcranes.com.